nixfiles/home-aps.md

Home wireless APs

Reference for the home Wi-Fi access points. Like the switches (home-switches.md), these are not managed by this flake — they are configured on-device (RouterOS on the MikroTik, OpenWrt/UCI on the Cudy). This file documents the shared VLAN/trunk design and each AP.

Only the DNS records live in the flake (nixos/boxes/home/routing-common/dns.nix, h.nul.ie zone). Everything else here is applied by hand on the device.

The APs

	vibe	wave
Model	MikroTik cAP ax (cAPGi-5HaxD2HaxD)	Cudy AX3000 (OpenWrt id cudy,ap3000-v1)
OS	RouterOS 7.x	OpenWrt 25.12.x (MT7981B / Filogic 820)
Radio	2×2 both bands	2×2 both bands (2 spatial streams)
Uplink	trunk (multi-port; ether2 is a wired LAN port)	single 2.5 GbE trunk
Management	core/hi/lo .15	core/lo .14 (not hi; see below)

Both mirror the same two SSIDs. wave replaced an older AP of the same name; the new one is the Cudy running OpenWrt.

Note on "AX3000": MT7981B is 2×2 (2 spatial streams). The "3000" is aggregate Mbps — 574 (2.4 GHz 2ss) + 2402 (5 GHz 2ss @ 160 MHz) — not three streams. iw confirms 2×2 (Available Antennas TX/RX 0x3; "3 streams: not supported"). 160 MHz is what earns the "3000".

Shared design (dumb AP)

Every AP is a dumb AP: it bridges wireless clients onto the right VLAN and does no routing, DHCP, RA or firewalling. The home routers (river/stream) own DHCP/RA/gateway (per-VLAN VRRP VIPs) and firewalling. The uplink is a tagged trunk:

VLAN	lib.my.c.home.vlans	Role	AP use
— (native)	core	switch/fabric management (1500)	backup management (untagged)
100	hi	trusted LAN, high-MTU (jumbo 9000)	vibe management (it's jumbo-capable)
110	lo	trusted LAN (1500)	main SSID wlan0; wave management
120	untrusted	guest network	guest SSID wlan1

hi and lo are both trusted client VLANs — the only difference is MTU (hi carries jumbo 9000, lo is standard 1500). An AP puts its own management on whichever it can do: vibe (jumbo) sits on hi, wave (eth0 capped at 2026) sits on lo. The main SSID lands on lo because Wi-Fi clients are 1500 regardless.

SSIDs

SSID	Bands	Security	VLAN
wlan0 (main)	5 GHz + 2.4 GHz	WPA2/WPA3-PSK (sae-mixed)	110 (lo)
wlan1 (guest)	2.4 GHz	WPA2-PSK (psk2)	120 (untrusted)

Passphrases are never stored in this repo. vibe is the source of truth; read them out-of-band with ssh admin@vibe '/interface wifi export show-sensitive' (.passphrase= prints unquoted).

vibe (MikroTik cAP ax)

RouterOS, one hardware-offloaded bridge main with vlan-filtering=yes. Access: ssh admin@vibe — key auth for admin is installed (~/.ssh/id_rsa), with admin/admin as a fallback.

• Uplink ether1 — trunk, tagged VLANs 100/110/120; native/untagged is the default VLAN 1 (PVID, no IP). ether2 is a wired access port on VLAN 110 (lo). l2mtu 9214.
• Radios — wifi1 (5 GHz, 20/40/80) + wifi2 (2.4 GHz, 20/40) both broadcast wlan0 (WPA2/WPA3-PSK), untagged onto VLAN 110. wifi3 is a virtual AP on wifi2 broadcasting wlan1 (WPA2-PSK), untagged onto VLAN 120. country=Ireland.
• Bridge VLANs — 100 tagged main,ether1; 110 tagged main,ether1 + untagged ether2,wifi1,wifi2; 120 tagged main,ether1 + untagged wifi3.
• Management — jim/dave-style (core/hi/lo), on host .15: 192.168.64.15 on core (native/untagged, backup), 192.168.68.15/22 + 2a0e:97c0:4d0:1::1:6 on the hi VLAN-100 interface (holds the default route, via the hi VIP 192.168.71.254), and 192.168.72.15/21 + 2a0e:97c0:4d0:2::1:6 on lo VLAN 110. No IP on untrusted. l2mtu 9214, so hi carries jumbo (9000) here — vibe sits on hi because it can jumbo, unlike wave (see its MTU note).
• Roaming — 802.11k/v via a /interface wifi steering profile (rrm=yes wnm=yes, neighbor-group=home-aps) assigned to wifi1/wifi2/wifi3.
• Resolver — the hi VIP 192.168.71.254 / 2a0e:97c0:4d0:1::ffff.

wave (Cudy AX3000, OpenWrt)

Single-port AP, so the port is a VLAN trunk carrying management + both SSIDs.

Management addressing

wave takes host .14, on lo (primary) and core (backup) — deliberately not hi, unlike the switches and vibe. hi is the jumbo (9000) VLAN, but wave's eth0 caps at 2026 (see MTU note), so there's no reason to put it there; lo is 1500 with a proper VRRP VIP for the default route + resolver, and core has no VIP/v6 so it can only be a backup. No IP on untrusted. Records in dns.nix:

Name	VLAN	Address
wave-core	core (native/untagged)	192.168.64.14/24 — backup, like the switches (no VIP → backup only)
wave	lo 110	192.168.72.14/21, 2a0e:97c0:4d0:2::1:5 — primary; holds the default route + resolver (lo VIP 192.168.79.254 / 2a0e:97c0:4d0:2::ffff)

Firewall: management (SSH/LuCI) reachable from core/lo only; untrusted is a separate zone with input REJECT (and wave has no IP there) — no management via the guest VLAN.

brian switch port

wave hangs off brian (UniFi). Its port is a trunk: tagged VLAN 110/120 (lo + guest), and native/untagged = core (the fabric's management VLAN, carrying wave-core). VLAN 100 (hi) is not needed here — wave isn't on hi (see Management addressing). Configure via the UniFi controller (brian has no CLI); see home-switches.md.

Flashing OpenWrt (Cudy AX3000 / cudy_ap3000-v1)

Hardware: MT7981B, 512 MB RAM, 256 MB SPI-NAND, 1× 2.5 GbE (RTL8221B), 2×2 WiFi 6.

⚠️ Serial caveat: units with a serial starting 2543… (post ~Nov 2025) use a different flash chip and can brick with older firmware. Match firmware to the unit.

OpenWrt can't be flashed directly over stock. Two-stage, via a Cudy transition firmware (Cudy OpenWrt download page / support@cudy.com; warnning.txt in that bundle has the steps):

1. Stock Cudy UI: update to ≥ 2.4.7 (adds TFTP recovery.bin recovery), then flash the Cudy intermediate firmware (cudy_ap3000-v1-sysupgrade_*.bin), "keep settings" unchecked. It reboots into an OpenWrt-based build at 192.168.1.1 (SSH root, empty password).
2. From there, sysupgrade -n to vanilla OpenWrt (…-cudy_ap3000-v1-squashfs-sysupgrade.bin from downloads.openwrt.org; this release ships no factory image — sysupgrade only).

Stock default (out of box) is a DHCP client falling back to 192.168.10.254; the stock UI is a customised LuCI (only 80/443, no SSH) with a first-boot "create admin password" wizard — so the stock-side flashing is done from a browser, not headless.

On-device config notes

• Package manager is apk (not opkg). WiFi runs wpad-mbedtls (full — swapped from the default wpad-basic-mbedtls, which lacks 802.11v). 802.11k + 802.11v (ieee80211k + bss_transition) are enabled on all SSIDs. ⚠️ Swapping wpad live leaves the mac80211 vifs stuck in a start→teardown loop (nl80211 ... No such device); a wifi reload/network restart won't recover it — reboot after apk add wpad-mbedtls.
• Radios: radio0 = 2.4 GHz, radio1 = 5 GHz (keyed by band, don't assume). 5 GHz is pinned to channel 36 / HE160 (any 160 MHz block in IE is DFS; ch36 has the shortest ~60 s CAC).
• Bridge: br-lan with vlan_filtering, single port eth0 — tagged 110/120, untagged/PVID VLAN 1 (= native/core). SSIDs attach via network = lo/untrusted (= br-lan.110/.120).
• Dumb-AP: no DHCP pools, odhcpd.maindhcp=0, delegate=0 on the L3 interfaces.
• MTU: all interfaces are 1500. The mtk_eth_soc 2.5 GbE (eth0) caps at 2026 bytes (ip link set eth0 mtu 9000 → SIOCSIFMTU: Invalid argument), so wave can't join hi's jumbo (9000) fabric like vibe does — which is precisely why wave is managed on lo, not hi (see Management addressing). Nothing on wave needs > 1500.
• LuCI: enabled, login root / admin. SSH: key-only (PasswordAuth/RootPasswordAuth off).
• iperf3 installed for throughput testing.

Access

• SSH: ssh root@wave (key-only; wave/wave-core resolve once dns.nix is deployed).
• LuCI: http://192.168.72.14/ (or http://wave/), root / admin.