docs/boxes: Document deployed boxes
Add per-site and per-box inventories, consolidate shared network design, and relocate the switch and access-point references under the home site.
This commit is contained in:
@@ -0,0 +1,151 @@
|
||||
# Home wireless APs
|
||||
|
||||
Reference for the home Wi-Fi access points. Like the switches ([switches.md](switches.md)), these
|
||||
are **not** managed by this flake — they are configured on-device (RouterOS on the MikroTik,
|
||||
OpenWrt/UCI on the Cudy). This file documents the shared VLAN/trunk design and each AP.
|
||||
|
||||
Only the DNS records live in the flake
|
||||
([`nixos/boxes/home/routing-common/dns.nix`](../../../nixos/boxes/home/routing-common/dns.nix),
|
||||
`h.nul.ie` zone). Everything else here is applied by hand on the device.
|
||||
|
||||
## The APs
|
||||
|
||||
| | vibe | wave |
|
||||
|---|---|---|
|
||||
| Model | MikroTik **cAP ax** (`cAPGi-5HaxD2HaxD`) | Cudy **AX3000** (OpenWrt id `cudy,ap3000-v1`) |
|
||||
| OS | RouterOS 7.x | OpenWrt 25.12.x (MT7981B / Filogic 820) |
|
||||
| Radio | 2×2 both bands | 2×2 both bands (2 spatial streams) |
|
||||
| Uplink | trunk (multi-port; `ether2` is a wired LAN port) | single **2.5 GbE** trunk |
|
||||
| Management | core/hi/lo `.15` | core/lo `.14` (**not** `hi`; see below) |
|
||||
|
||||
Both mirror the same two SSIDs. `wave` replaced an older AP of the same name; the new one is the
|
||||
Cudy running OpenWrt.
|
||||
|
||||
> **Note on "AX3000":** MT7981B is 2×2 (2 spatial streams). The "3000" is *aggregate* Mbps —
|
||||
> 574 (2.4 GHz 2ss) + 2402 (5 GHz 2ss @ **160 MHz**) — not three streams. `iw` confirms 2×2
|
||||
> (`Available Antennas TX/RX 0x3`; "3 streams: not supported"). 160 MHz is what earns the "3000".
|
||||
|
||||
## Shared design (dumb AP)
|
||||
|
||||
Every AP is a **dumb AP**: it bridges wireless clients onto the right VLAN and does **no** routing,
|
||||
DHCP, RA or firewalling. The home routers (`river`/`stream`) own DHCP/RA/gateway (per-VLAN VRRP VIPs)
|
||||
and firewalling. The uplink is a **tagged trunk**:
|
||||
|
||||
| VLAN | `lib.my.c.home.vlans` | Role | AP use |
|
||||
|---|---|---|---|
|
||||
| — (native) | `core` | switch/fabric management (1500) | backup management (untagged) |
|
||||
| 100 | `hi` | trusted LAN, **high-MTU** (jumbo 9000) | `vibe` management (it's jumbo-capable) |
|
||||
| 110 | `lo` | trusted LAN (1500) | main SSID `wlan0`; `wave` management |
|
||||
| 120 | `untrusted` | guest network | guest SSID `wlan1` |
|
||||
|
||||
`hi` and `lo` are both **trusted** client VLANs — the only difference is MTU (`hi` carries jumbo
|
||||
9000, `lo` is standard 1500). An AP puts its own management on whichever it can do: `vibe` (jumbo)
|
||||
sits on `hi`, `wave` (eth0 capped at 2026) sits on `lo`. The main SSID lands on `lo` because Wi-Fi
|
||||
clients are 1500 regardless.
|
||||
|
||||
### SSIDs
|
||||
|
||||
| SSID | Bands | Security | VLAN |
|
||||
|---|---|---|---|
|
||||
| `wlan0` (main) | 5 GHz + 2.4 GHz | WPA2/WPA3-PSK (`sae-mixed`) | 110 (`lo`) |
|
||||
| `wlan1` (guest) | 2.4 GHz | WPA2-PSK (`psk2`) | 120 (`untrusted`) |
|
||||
|
||||
**Passphrases are never stored in this repo.** `vibe` is the source of truth; read them out-of-band
|
||||
with `ssh admin@vibe '/interface wifi export show-sensitive'` (`.passphrase=` prints **unquoted**).
|
||||
|
||||
## vibe (MikroTik cAP ax)
|
||||
|
||||
RouterOS, one hardware-offloaded bridge `main` with `vlan-filtering=yes`. Access: `ssh admin@vibe`
|
||||
— key auth for `admin` is installed (`~/.ssh/id_rsa`), with `admin`/`admin` as a fallback.
|
||||
|
||||
- **Uplink `ether1`** — trunk, tagged VLANs 100/110/120; native/untagged is the default VLAN 1
|
||||
(PVID, no IP). `ether2` is a wired **access port** on VLAN 110 (`lo`). `l2mtu 9214`.
|
||||
- **Radios** — `wifi1` (5 GHz, 20/40/80) + `wifi2` (2.4 GHz, 20/40) both broadcast `wlan0`
|
||||
(WPA2/WPA3-PSK), untagged onto VLAN 110. `wifi3` is a virtual AP on `wifi2` broadcasting `wlan1`
|
||||
(WPA2-PSK), untagged onto VLAN 120. `country=Ireland`.
|
||||
- **Bridge VLANs** — 100 tagged `main,ether1`; 110 tagged `main,ether1` + untagged
|
||||
`ether2,wifi1,wifi2`; 120 tagged `main,ether1` + untagged `wifi3`.
|
||||
- **Roaming** — 802.11k/v via a `/interface wifi steering` profile (`rrm=yes wnm=yes`,
|
||||
`neighbor-group=home-aps`) assigned to `wifi1`/`wifi2`/`wifi3`.
|
||||
- **Resolver** — the hi VIP `192.168.71.254` / `2a0e:97c0:4d0:1::ffff`.
|
||||
|
||||
### Management
|
||||
|
||||
Management uses host `.15`: `192.168.64.15` on native/core as a backup,
|
||||
`192.168.68.15/22` + `2a0e:97c0:4d0:1::1:6` on `hi` VLAN 100, and
|
||||
`192.168.72.15/21` + `2a0e:97c0:4d0:2::1:6` on `lo` VLAN 110. The `hi` address holds the default
|
||||
route through its VIP; `untrusted` has no address. With `l2mtu 9214`, `vibe` can use the jumbo
|
||||
`hi` network unlike `wave`.
|
||||
|
||||
## wave (Cudy AX3000, OpenWrt)
|
||||
|
||||
Single-port AP, so the port is a VLAN **trunk** carrying management + both SSIDs.
|
||||
|
||||
### Management addressing
|
||||
|
||||
`wave` takes host `.14`, on **`lo` (primary) and `core` (backup)** — deliberately **not** `hi`,
|
||||
unlike the switches and `vibe`. `hi` is the jumbo (9000) VLAN, but `wave`'s eth0 caps at 2026 (see
|
||||
MTU note), so there's no reason to put it there; `lo` is 1500 with a proper VRRP VIP for the default
|
||||
route + resolver, and `core` has no VIP/v6 so it can only be a backup. No IP on `untrusted`. Records
|
||||
in `dns.nix`:
|
||||
|
||||
| Name | VLAN | Address |
|
||||
|---|---|---|
|
||||
| `wave-core` | core (native/untagged) | `192.168.64.14/24` — backup, like the switches (no VIP → backup only) |
|
||||
| `wave` | lo 110 | `192.168.72.14/21`, `2a0e:97c0:4d0:2::1:5` — primary; holds the default route + resolver (lo VIP `192.168.79.254` / `2a0e:97c0:4d0:2::ffff`) |
|
||||
|
||||
**Firewall:** management (SSH/LuCI) reachable from `core`/`lo` only; `untrusted` is a separate
|
||||
zone with `input REJECT` (and `wave` has no IP there) — **no management via the guest VLAN**.
|
||||
|
||||
### brian switch port
|
||||
|
||||
`wave` hangs off **brian** (UniFi). Its port is a **trunk**: tagged VLAN **110/120** (`lo` + guest),
|
||||
and **native/untagged = core** (the fabric's management VLAN, carrying `wave-core`). VLAN 100 (`hi`)
|
||||
is **not** needed here — `wave` isn't on `hi` (see Management addressing). Configure via the UniFi
|
||||
controller (brian has no CLI); see [switches.md](switches.md).
|
||||
|
||||
### Flashing OpenWrt (Cudy AX3000 / `cudy_ap3000-v1`)
|
||||
|
||||
Hardware: MT7981B, 512 MB RAM, 256 MB SPI-NAND, 1× 2.5 GbE (RTL8221B), 2×2 WiFi 6.
|
||||
|
||||
> ⚠️ **Serial caveat:** units with a serial starting `2543…` (post ~Nov 2025) use a different flash
|
||||
> chip and can brick with older firmware. Match firmware to the unit.
|
||||
|
||||
OpenWrt can't be flashed directly over stock. Two-stage, via a Cudy **transition** firmware (Cudy
|
||||
OpenWrt download page / `support@cudy.com`; `warnning.txt` in that bundle has the steps):
|
||||
|
||||
1. Stock Cudy UI: update to **≥ 2.4.7** (adds TFTP `recovery.bin` recovery), then flash the Cudy
|
||||
**intermediate** firmware (`cudy_ap3000-v1-sysupgrade_*.bin`), "keep settings" **unchecked**.
|
||||
It reboots into an OpenWrt-based build at `192.168.1.1` (SSH `root`, empty password).
|
||||
2. From there, `sysupgrade -n` to vanilla OpenWrt (`…-cudy_ap3000-v1-squashfs-sysupgrade.bin` from
|
||||
`downloads.openwrt.org`; this release ships **no** factory image — sysupgrade only).
|
||||
|
||||
Stock default (out of box) is a DHCP client falling back to **`192.168.10.254`**; the stock UI is a
|
||||
customised LuCI (only 80/443, no SSH) with a first-boot "create admin password" wizard — so the
|
||||
stock-side flashing is done from a browser, not headless.
|
||||
|
||||
### On-device config notes
|
||||
|
||||
#### Wireless packages
|
||||
|
||||
The package manager is `apk`, not `opkg`. Wi-Fi uses the full `wpad-mbedtls` package so all SSIDs
|
||||
can enable 802.11k/v (`ieee80211k` + `bss_transition`). Replacing `wpad-basic-mbedtls` live leaves
|
||||
the mac80211 interfaces in a start/teardown loop that reloads cannot recover; reboot after
|
||||
`apk add wpad-mbedtls`.
|
||||
|
||||
- Radios: `radio0` = 2.4 GHz, `radio1` = 5 GHz (keyed by `band`, don't assume). 5 GHz is pinned to
|
||||
**channel 36 / HE160** (any 160 MHz block in IE is DFS; ch36 has the shortest ~60 s CAC).
|
||||
- Bridge: `br-lan` with `vlan_filtering`, single port `eth0` — tagged `110/120`, untagged/PVID
|
||||
VLAN 1 (= native/core). SSIDs attach via `network` = `lo`/`untrusted` (= `br-lan.110`/`.120`).
|
||||
- Dumb-AP: no DHCP pools, `odhcpd.maindhcp=0`, `delegate=0` on the L3 interfaces.
|
||||
- **MTU:** all interfaces are **1500**. The `mtk_eth_soc` 2.5 GbE (`eth0`) caps at **2026 bytes**
|
||||
(`ip link set eth0 mtu 9000` → `SIOCSIFMTU: Invalid argument`), so `wave` can't join `hi`'s jumbo
|
||||
(9000) fabric like `vibe` does — which is precisely **why `wave` is managed on `lo`, not `hi`**
|
||||
(see Management addressing). Nothing on `wave` needs > 1500.
|
||||
- **LuCI:** enabled, login `root` / `admin`. **SSH:** key-only (`PasswordAuth`/`RootPasswordAuth off`).
|
||||
- `iperf3` installed for throughput testing.
|
||||
|
||||
### Access
|
||||
|
||||
- SSH: `ssh root@wave` (key-only; `wave`/`wave-core` resolve once `dns.nix` is deployed).
|
||||
- LuCI: `http://192.168.72.14/` (or `http://wave/`), `root` / `admin`.
|
||||
Reference in New Issue
Block a user