docs/home: Add 5G WWAN modem reference

Notes from bench-testing the Quectel RM500U-EA on tower, bought to
eventually replace stream's Virgin Media WAN. Like the switches and
APs, the module is configured out-of-band and is not referenced by
the flake.

Records what it takes to connect at all: the module must be switched
from its stock NCM composition to MBIM, since under NCM the PDP
context activates but the cdc_ncm link never raises carrier; and the
connect only succeeds with the network-expanded APN read off the
default-attach bearer, as IPv4.

Also flags the two consequences for stream: the SIM is CGNAT so it
cannot carry the public lease stream's WAN currently publishes, and
the bearer reports a /8 that would cover Tailscale's 100.64.0.0/10
if configured literally.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>

docs/sites/home/README.md

@@ -43,3 +43,9 @@ documented in [switches.md](switches.md).
 The Wi-Fi APs — `vibe` (MikroTik cAP ax) and `wave` (Cudy AX3000 on OpenWrt) — are dumb APs, also
 **not** managed by this flake. The shared VLAN-trunk design, SSIDs, per-AP management addressing,
 and the OpenWrt flash/config for `wave` are in [aps.md](aps.md).
+
+## 5G WWAN
+
+A Quectel RM500U-EA USB modem with a GoMo SIM is being evaluated as a replacement for `stream`'s
+Virgin Media WAN. It is bench-tested only and not yet referenced by the flake; the module settings
+it needs, the APN gotcha and the CGNAT consequences are in [wwan.md](wwan.md).

docs/sites/home/stream.md

@@ -33,6 +33,10 @@ See the consolidated [network assignments](../../networking.md#box-assignments)
 
 ## WAN (Virgin Media DHCP)
 
+A Quectel RM500U-EA 5G modem is being evaluated as a replacement for this WAN; it is bench-tested
+only and nothing here depends on it yet. Note that its SIM is CGNAT, so it cannot carry the public
+lease this section assumes — see [wwan.md](wwan.md).
+
 ### Link and addressing
 
 `wan` is a renamed igc NIC (`00:f0:cb:ee:ca:dd`) towards the cable modem. The modem segment is

docs/sites/home/wwan.md

@@ -0,0 +1,139 @@
+# Home 5G WWAN modem
+
+Reference for the Quectel **RM500U-EA** USB 5G modem, bought to eventually replace `stream`'s
+Virgin Media cable WAN ([stream.md](stream.md)). Like the switches ([switches.md](switches.md)) and
+the APs ([aps.md](aps.md)), it is **not** managed by this flake: the module's own settings live in
+its NVRAM and are applied out-of-band over AT, and nothing in the repo references it yet.
+
+As of 2026-08-05 it has only been bench-tested on `tower`; `stream` is untouched. The notes below
+are the working knowledge from that session — what the module needs in order to connect at all, and
+what is still unresolved.
+
+## The hardware
+
+| | |
+|---|---|
+| Model | Quectel **RM500U-EA** |
+| Platform | UNISOC-based (not Qualcomm) — its AT set is the `AT+QCFG`/`AT+QNETDEVCTL` router-firmware family, not the QMI one |
+| USB | `2c7c:0900`, SuperSpeed (USB 3.1) |
+| Firmware | `RM500UEAAAR03A13M2G` |
+| SIM | **GoMo**, which rides eir's network (MCC/MNC **272-03**, AS**15751** Meteor Mobile) |
+
+The SIM's **PIN lock has been disabled** on the SIM itself, so no PIN needs to be entered at boot
+and no age secret is required for it. Card identifiers and the PIN are deliberately not recorded
+here; read them from the modem with `mmcli` if needed.
+
+## The module must be in MBIM mode
+
+This is the single most important setting. The module ships in **NCM** mode (`AT+QCFG="usbnet",5`),
+and in that mode it does not work:
+
+- The PDP context comes up correctly — `AT+CGPADDR` reports a real address and `AT+CGCONTRDP`
+  reports the APN, DNS servers and prefix — but the `cdc_ncm` interface **never raises carrier**, so
+  no traffic can leave the box. No combination of `AT+QNETDEVCTL` modes (the `(0-3)` operations,
+  per profile) changed that.
+- ModemManager also mis-reports the module's capability as `gsm-umts` only, and cannot read signal
+  quality (it sits at 0% while the radio is registered and attached).
+
+Switching to **MBIM** fixes both:
+
+```
+AT+QCFG="usbnet",2
+AT+CFUN=1,1          # reset so the new USB composition takes effect
+```
+
+It then enumerates as `cdc_mbim` with `/dev/cdc-wdm0` and a `wwp*` interface, ModemManager reports
+`gsm-umts, lte, 5gnr`, signal quality works, and carrier follows the bearer. The other `usbnet`
+values the module advertises are `(1,2,3,5,11,13,15)` — `1` ECM, `2` MBIM, `3` RNDIS, `5` NCM.
+
+To reach the AT ports (`ttyUSB2` and `ttyUSB3` are the AT ones; ModemManager claims them, so stop it
+first), any serial terminal works — `minicom -D /dev/ttyUSB2`, or a raw `stty`/`exec` pair on the
+device node.
+
+### Router-mode features are not in use
+
+The firmware is the router variant: it can do its own NAT (`AT+QCFG="nat"`) and hand the host a
+lease off a private LAN prefix (`AT+QCFG="lanip"`, default `192.168.42.0/24`). It is currently in
+bridge mode (`nat=0`) so the host gets the real WAN address. NAT mode was not needed once MBIM
+worked, and would mean double NAT.
+
+## Connecting: the APN must be the network-expanded form
+
+The documented consumer APNs (`gomo.ie`, `data.myeirmobile.ie`) **fail**. The connect only succeeds
+with the fully expanded name the network itself uses, and only as **IPv4**:
+
+```
+mmcli -m <n> --simple-connect="apn=data.myeirmobile.ie.mnc003.mcc272.gprs,ip-type=ipv4"
+```
+
+The module has `AT+QCFG="autoapn",1`, so it selects an APN by itself during attach and brings up an
+initial EPS bearer regardless. That bearer is where the expanded name comes from: list the modem's
+bearers and read the one whose type is `default-attach`.
+
+```
+mmcli -m <n>          # note the bearer paths and the initial bearer path
+mmcli -b <n>          # the default-attach bearer carries the real APN
+```
+
+Failure modes are worth distinguishing, since they look similar from `mmcli`:
+
+| Symptom | Meaning |
+|---|---|
+| `MBIM status error: Failure`, immediate | The APN reached the network and was rejected — usually the wrong APN string |
+| `Network timeout`, after a long wait | The APN never resolved to anything; wrong name entirely |
+| `No valid data port found` | Already connected — the single data port is in use by an existing bearer |
+
+## Bench result on tower
+
+Measured 2026-08-05 on `tower`, indoors, with **no external antennas** and a weak signal
+(RSSI around −85 dBm):
+
+| | |
+|---|---|
+| Access technology | `lte, 5gnr` — 5G **NSA** |
+| Throughput | ~64 Mbit/s down, ~26 Mbit/s up |
+| Latency | ~76 ms to `1.1.1.1` |
+| Bearer-negotiated rates | 150 Mbit/s down, 50 Mbit/s up |
+
+Treat the throughput as a floor, not a characterisation — antennas and siting were both worst-case.
+
+## The address is CGNAT, and the prefix length is a trap
+
+Two separate consequences of how the bearer addresses the host.
+
+### No public IP
+
+The bearer address is in `100.64.0.0/10` and egress is carrier-NAT'd (`*.cgn1.srl.meteor.ie`,
+AS15751). There is **no inbound reachability and no public address**. `stream` currently takes a
+*public* DHCP lease on `wan` and publishes it — see [stream.md](stream.md#wan-virgin-media-dhcp),
+which also drives `my.homeRouter.dns.wanSkipBroadcasts`. Replacing that WAN with this SIM therefore
+drops port forwards, inbound WireGuard and anything resolving to `stream`'s WAN address. Making
+this a real WAN needs either a public/static IP from the carrier, or `stream`'s inbound
+reachability moved onto the AS211024 mesh or a tunnel from `britway`
+([networking.md](../../networking.md)).
+
+### The bearer reports a /8
+
+ModemManager reports the address with a **`/8` prefix**, i.e. `100.0.0.0/8`. Configuring that
+literally would install a route covering **Tailscale's `100.64.0.0/10`** and break it. Any
+configuration for this modem must add the address as a `/32` with an explicit on-link route to the
+gateway, and never use the bearer's own prefix length.
+
+For a throwaway test that cannot disturb the box, put the address and default route in their own
+routing table behind an `ip rule` matching the source address, and drive traffic onto it with
+`ping -I <addr>` / `curl --interface <addr>`.
+
+## Still open
+
+- **IPv6.** GoMo is expected to provide it, but `ip-type=ipv4v6` fails to connect and only
+  `ip-type=ipv4` works. In NCM mode the module *did* report an IPv6 address and IPv6 DNS servers
+  (`2001:bb0::11`/`::12`) on the context, so the network clearly offers it — this looks like an APN
+  or MBIM-session problem rather than a carrier one. Worth retrying with a separate IPv6-only
+  context, or with the initial EPS bearer settings pinned via
+  `mmcli --3gpp-set-initial-eps-bearer-settings`.
+- **A public or static IP** from GoMo/eir, without which this cannot replace `stream`'s WAN
+  unchanged (see above).
+- **Antenna siting**, and whether 5G **SA** is reachable rather than the NSA seen so far.
+- **Flake integration** — nothing exists yet. It would need the MBIM interface configured under
+  `stream`'s networkd, a `wan-online.target` mechanism equivalent to the current DHCP-route gate,
+  and a decision on whether ModemManager or a plain `mbimcli` connect script drives the bearer.